[. . . ] ECO2437 355mm(14") CUT-OFF SAW OWNER'S OPERATION MANUAL 17 18 13 2 1 12 11 10 5 9 6 7 8 3 4 22 Fig. 1 23 15 14 16 19 3 11 22 20 10 21 8 Fig. 2 24 25 26 27 2 28 29 30 Fig. 3 3 32 31 b Fig. 4 a Fig. 5 Fig. 6 Fig. 7 Fig. 8 Fig. 9 Fig. 10 Fig. 11 Fig. 12 Fig. 13 33 34 Fig. 14 ENGLISH RULES FOR SAFE OPERATION USE SAFETY GLASSES Use face or dust mask if the cutting operation is dusty. Safe operation of this power tool requires that you read and understand this operator's manual and all labels affixed to the tool. Safety is a combination of common sense, staying alert, and knowing how your cut-off machine works. When not in use, before servicing, or when changing attachments, wheels, bits, cutters, etc. , all tools should be disconnected. [. . . ] Clean outer flange, then align flats with flats on wheel arbor and slide it onto arbor until it is flushed against wheel. Place recessed side of outer washer against arbor, then insert wheel bolt into threaded end of wheel arbor. Pull the spindle lock button and rotate bolt until spindle being locked. This will secure the fence in place at desired angle. ADJUSTING WIDTH OF CUT (Fig. 5-6) Unplug your cut-off machine. WARNING: Failure to unplug cut-off machine could result in accidental starting causing possible serious personal injury. By following the below adjustment procedures, it is possible to increase that distance so that the vice is between 35 mm and 205 mm or 70 mm and 240 mm from the fence. WARNING: Bevel cutting angle is not suitable for the above 2 suggested width of cuts. To increase the width of cut of your cut-off machine, loosen and remove the fence quick lock and washer. The use the wrench supplied to loosen and remove the fence bolt and washers to secure fence to machine base. Reposition the curved slot of the fence with the threaded hole (b) at the back of the machine base. Align remaining fence bolt hole with the middle threaded hole (a) of the machine base. Install fence bolt through lock washer and flat washer into machine base. This position is good for cutting thin and wide pieces of stock, such as flat or angled stock. To increase the height of cut of your cut-off machine, follow the above procedure except place the rear fence bolt in the middle threaded hole (a) and the front fence bolt in the front threaded hole. Using the wrench provided, securely tighten fence quick lock en fence bolts. This position is good for cutting tall and thick pieces of stock, such as square or tube stock. WARNING: Do not overtighten wheel bolt. Overtightening can cause the new wheel to crack, resulting in premature failure and possible serious personal injury. PROTECTION GUARD In order to avoid spark splashing, under the operational condition, loose the screw and adjust angle of the protection guard. ADJUSTABLE FENCE (Fig. 4) The adjustable fence is located at the rear of your cut-off machine. It is used along with the vice clamp to provide a clamp for holding your workpiece securely when making cuts. The fence can be rotated to obtain cutting angles from 0° to 45° (L&R). It can also be moved back to allow greater cutting widths in thin stock, or moved forward to allow greater cutting depths in tall or thick stock. CUTTING ANGLE ADJUSTMENT (Fig. 4) Unplug your cut-off machine. WARNING: Failure to unplug cut-off machine could result in accidental starting causing possible serious personal injury. Rotate fence until the desired angle of cut on the scale is aligned with the indicator in machine base. [. . . ] To avoid accidental start up of your cut-off machine, always make sure the switch is off before connecting to power source. Never perform any cutting operation freehand (without placing workpiece in the vice). Before turning on machine, perform a dry run of the cutting operation just to make sure that no problems will occur when the cut is made. Start the machine by grasping the handle and fully squeezing the switch trigger. [. . . ]